Village QV36D-A Owner's Manual download pdf (Page 20)

Quadra-Fire • QV36DB-A • 2018-900 Rev. F • 12/07

Figure 17.

B. Installing Vent Components

After determining which set of starting collars will be used

(top or rear), follow venting instructions accordingly.

Venting Out the Rear Vent

Remove the installed rear seal cap from the rear starting

collars by cutting the strap at each end. (see Figure 17).

Follow the vent configuration tables accordingly.

Remove the insulation from the REAR five inch flue, pull

the heat shield out from outside of the firebox.

WARNING: THE TOP HEAT SHIELD (INSIDE THE

FIREBOX) MUST REMAIN ATTACHED IF THE

VENT SYSTEM IS ATTACHED TO THE REAR

STARTING COLLARS. SEE FIGURE 17.

Venting Out the Top Vent

Remove the two screws in the top vent collar seal cap and

remove the top vent collar seal cap and the two pieces of

insulation inside the top two starting collars (See Figure 17).

Remove the heat shield from inside the TOP five inch flue

from outside of the firebox.

You have to take the glass off again for positioning the logs

when the unit is finally installed in place and finished around

it. Re-install the glass door. Attach vent system to the top

starting collars.

WARNING: FAILURE TO REMOVE INSULA-

TION IN THE SET OF COLLARS YOU ARE US-

ING COULD CAUSE A FIRE.

WARNING: THE REAR VENT COLLAR SEAL

CAP MUST REMAIN ATTACHED TO THE REAR

VENT COLLARS IF THE VENT SYSTEM IS ATTACHED

TO THE TOP STARTING COLLARS. SEE FIGURE 18.

WARNING: YOU MUST LEAVE THE INSULA-

TION IN PLACE IN THE SET OF COLLARS YOU

ARE NOT USING.

If your vertical vent component is over 10 feet, you may

want to install the included vertical baffle to improve flame

appearance. Vertical baffle is located in the bag containing

the instruction manual. Center the vertical baffle on the five

inch flue being used, and with self tapping screws secure

the baffle to the inside of the firebox.

Cut the seal cap

strap and remove white

gasket material.

CUT

HERE

Venting Out Rear

Venting Out Top

HEAT

SHIELD

DISCARD

INSULATION

and

HEAT SHIELD

HEAT

SHIELD

INSULATION

DISCARD BOTH

PIECES and

HEAT SHIELD

SEAL

CAP

SEAL

CAP

1. Attach the First Vent Component to the

Starting Collars

To attach the first vent component to the starting collars of

the fireplace:

• Make sure that the fiberglass gasket supplied in the

manual bag seals between the first 8 inch (203mm)

vent component and the outer fireplace wrap. Using 2

self-tapping screws from the manual bag secure that

gasket to the outer wrap (see Figure 18).

Figure 18. Fiberglass Gasket

FIRST VENT

COMPONENT

FIBERGLASS

GASKET

OUTER

WRAP

DVP PIPE:

2. Assembling Vent Sections

Refer to Cinch Pipe and Termination Cap installation in-

structions.

1. Attaching the Venting to the Fireplace

Refer to Cinch Pipe and Termination Cap installation in-

structions.

WARNING: ENSURE THAT THE FIBERGLASS

GASKET SUPPLIED WITH THE FIREPLACE

SEALS BETWEEN THE FIRST VENT COMPONENT

AND THE OUTER FIREPLACE WRAP.

If the installation is for a termination cap attached directly

to the fireplace, skip to the sections, Install Firestops and

Vent Termination.

3. Continue Adding Vent Components

WARNING: INSTALLATION OF THIS FIRE-

PLACE REQUIRES THE USE OF A HEAT

SHIELD ABOVE THE FIRST 90

ELBOW IN THE

VENTING SYSTEM.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 36 37

Comments to this Manuals

No comments

Village QV36D-A Owner's Manual Page 20

Comments to this Manuals

Related products and manuals for Fireplaces Village QV36D-A